Stage Layout Setup / 讲台布局安装

🎭 Stage Team / 讲台组

Team Information / 小组信息

🇬🇧 English Instructions

Purpose
Prepare the stage area, install the SPK-4 and SPK-5 loudspeaker groups, route and protect stage audio cables, position microphones, mark participant positions, and confirm the stage is ready for testing and walk-throughs.

Required References

• Full Drawing Set: 📎 Complete PDF
• Congregation Job Hazard Analysis (DC-85): 📁 Google Drive Folder
• CO-160a: 📎 CO-160a — Chapter 3, Audio Signal Cables (ASC-xx), pages 7–8
• Specific Schematics:
  • 1-1 Seating Layout Plan
  • 4-1 Stage Area Equipment Layout Large Scale View
  • 6-1 Audio Headend Wiring Diagram
  • 6-3 Audio Loudspeaker Wiring Diagram
  • 6-8 Audio Equipment Schedule
• Event Content List: Cases MS-1, ASC-01, WM-1, PLS-1 (SPK-4.1 and SPK-4.2), ALS-4

🗺️ View Stage Schematics (Pages 1-1, 4-1, 6-1, 6-3, 6-8)

Required Equipment Cases

• MS-1: 6 manual floor microphone stands with adjustable booms.
• ASC-01: XLR audio cables in 5 m, 10 m, and 20 m lengths. Shared with the Audio Cabling Team.
• WM-1: 1 SHURE SLXD4D dual receiver and 2 SHURE BETA 58A handheld wireless microphones (MIC-5 and MIC-6). The Power Distribution Team handles receiver setup and synchronization; the Stage Team coordinates placement and use.
• PLS-1: Contains SPK-4.1 and SPK-4.2. The Stage Team installs these two stage monitor loudspeakers.
• ALS-4: Contains SPK-5.1 and SPK-5.2.
• AHEC-1 — Shared Equipment: Wired lectern and participant microphones are stored inside AHEC-1.
• Local Equipment: Stage clock and megaphone.

Safety Notes

⚠️ Safety & Cable Handling
• Keep participant walkways clear and protect cables wherever they cross a walkway.
• Where possible, do not run XLR audio cables directly parallel to power cables; cross power cables at right angles.
• Make sure connected equipment is switched off before connecting XLR audio cables.
• Keep the attached Velcro with ASC-01 cables and do not use your elbow to wind them.
• Connect the XLR cable before installing a microphone on a boom or stand.
• Keep liquids away from equipment.

Setup Steps

1. Prepare the Stage
Schematics: Pages 1-1 Seating Layout Plan, 4-1 Stage Area Equipment Layout Large Scale View

• First: Assist the Loudspeakers Team with chair measurements, including loudspeaker positions, stage position, aisles, seating sections, and related spacing.
• Confirm the positions of SPK-4.1, SPK-4.2, SPK-5.1, and SPK-5.2.
• Install and position the lectern according to the stage layout.
• Remove old or distracting tape.
• Check the stage surface and participant paths for trip hazards.
• Confirm the stage layout follows the schematics.
• Keep the area clear for Audio Crew and Video Crew work.

2. Install SPK-4 and SPK-5
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-3 Audio Loudspeaker Wiring Diagram

• Retrieve SPK-4.1 and SPK-4.2 from PLS-1.
• Retrieve SPK-5.1 and SPK-5.2 from ALS-4.
• Position all four loudspeakers according to the schematics.
• Place SPK-4.1 and SPK-4.2 horizontally on their sides.
• Position SPK-5.1 and SPK-5.2 according to the locations and orientation shown.
• Leave sufficient space for safe cable connections.

⚠️ Important: SPK-4.1 and SPK-4.2 are stage monitor loudspeakers and must remain horizontally positioned on their sides.

3. Route, Connect, and Protect Stage Audio Cables
Reference: CO-160a, Chapter 3 — Audio Signal Cables (ASC-xx), pages 7–8
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-1 Audio Headend Wiring Diagram, 6-3 Audio Loudspeaker Wiring Diagram

• For ASC-01 XLR cables, open the attached Velcro and unwind the cable by rolling it off. Do not remove the Velcro.
• MIC-1, MIC-2, MIC-3, MIC-4: Route XLR cables from the stage microphones to AMC-1.
• SPK-4.1 and SPK-4.2: Route and connect the speakON loudspeaker cables.
• SPK-5.1 and SPK-5.2: Route and connect the XLR audio cables.
• Coordinate with the Power Distribution Team for SPK-5.1 and SPK-5.2 power.
• Where possible, avoid routing XLR audio cables directly parallel to power cables; cross power cables at right angles.
• Route cables neatly along the front edge of the stage and away from participant walking paths.
• Secure stage cables using small pieces of tape where required.
• Use appropriate cable protection wherever cables cross or enter a walkway.
• Confirm every cable is connected to the correctly labeled microphone or loudspeaker.

4. Label and Position Microphones
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-1 Audio Headend Wiring Diagram

• Label each wired microphone cable with its microphone assignment or use.
• Place one tag at the AMC-1 end and another approximately 2 meters from the microphone.
• Connect the XLR cable before installing the microphone on its boom or stand.
• Position the lectern, chairman, and participant microphones according to the stage layout and program needs.
• The Power Distribution Team handles WM-1 receiver setup, frequency scan, and synchronization.
• After WM-1 synchronization is complete, coordinate the placement and use of MIC-5 and MIC-6 on stage.
• Coordinate with the Audio Crew for final microphone and loudspeaker testing.

5. Mark Participant Positions
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

• Mark the positions for interviews, Watchtower comments, and their microphone stands.
• Keep markings discreet but clearly visible to participants and stage attendants.

6. Confirm Stage Readiness

• Confirm the stage clock is in its designated position and clearly visible.
• Place the megaphone in the agreed, easily accessible location.
• Confirm SPK-4, SPK-5, and all microphones have been tested with the Audio Crew.
• Check that all stage cables are secure and participant paths remain clear.
• Confirm the stage is ready for walk-throughs.

Completion Checklist

• Loudspeakers Team assisted with measurements
• Stage layout and lectern position confirmed
• Stage and participant paths clear of trip hazards
• SPK-4.1 and SPK-4.2 positioned horizontally on their sides
• SPK-5.1 and SPK-5.2 positioned according to the schematics
• SPK-4 speakON cables connected
• SPK-5 XLR audio cables connected
• SPK-5 power coordinated with the Power Distribution Team
• MIC-1 through MIC-4 XLR cables routed and protected
• Microphone cables labeled at the AMC-1 end and approximately 2 m from the microphone
• Audio and power cable routes separated where possible
• Walkway crossings protected
• Wired microphones positioned correctly
• WM-1 placement coordinated after Power Distribution setup and synchronization
• SPK-4, SPK-5, and microphones tested with the Audio Crew
• Participant and microphone stand positions marked
• Stage clock and megaphone in place
• Keyman inspection completed

Dismantling

• Wait for the department briefing and prayer 30 minutes after the program ends on Sunday before dismantling.
• Remove tape and cable protection carefully, and leave the stage area clean.
• Bring all Stage Team equipment, cables, microphones, stands, loudspeakers, accessories, stage clock, and megaphone to the designated equipment area for inventory.
• Coil ASC-01 XLR cables carefully. Do not use your elbow, and secure each cable with its attached Velcro.
• Coil remaining cables neatly, avoiding twists, kinks, and sharp bends.
• Check the stage area for any forgotten equipment or materials.
• Keyman confirms all Stage Team materials have been brought to the inventory area.

🇨🇳 中文说明

目的
按照图纸准备讲台区域，安装 SPK-4 和 SPK-5 扬声器组，铺设并保护讲台音频线缆，摆放麦克风，标记节目参与者位置，并确认讲台已准备好进行测试和走位练习。

参考资料

• 完整图纸： 📎 完整 PDF 文件
• 《会众工作危险性分析》(DC-85)： 📁 Google Drive 文件夹
• CO-160a： 📎 CO-160a — 第 3 章，Audio Signal Cables (ASC-xx)，第 7–8 页
• 相关图纸：
  • 1-1 座位布局图
  • 4-1 舞台区域设备布局大比例图
  • 6-1 音频主控接线图
  • 6-3 讲台及部门扬声器接线图
  • 6-8 音频设备清单
• 大会设备清单： 设备箱 MS-1、ASC-01、WM-1、PLS-1（SPK-4.1 和 SPK-4.2）及 ALS-4

🗺️ 查看讲台相关图纸（图纸 1-1, 4-1, 6-1, 6-3, 6-8）

所需设备箱

• MS-1： 6 个带可调节麦克风悬臂的落地麦克风架。
• ASC-01： 5 米、10 米和 20 米 XLR 音频线缆。与音频布线组共用。
• WM-1： 1 台 SHURE SLXD4D 双通道无线接收机及 2 支 SHURE BETA 58A 手持无线麦克风（MIC-5 和 MIC-6）。电源分配组负责接收机设置和同步；讲台组负责协调麦克风的摆放和使用。
• PLS-1： 包含 SPK-4.1 和 SPK-4.2。讲台组负责安装这两只讲台监听扬声器。
• ALS-4： 包含 SPK-5.1 和 SPK-5.2。
• AHEC-1 — 共用设备： 有线讲台麦克风和节目参与者麦克风存放在 AHEC-1 内。
• 本地设备： 讲台时钟和手提扩音器。

安全提醒

⚠️ 安全与线缆处理
• 保持节目参与者通道畅通，线缆穿过通道时必须加以保护。
• 在可行的情况下，不要让 XLR 音频线与电源线直接平行铺设；需要交叉时，应以直角交叉。
• 连接 XLR 音频线前，确认所连接的设备已经关闭。
• ASC-01 线缆原有的魔术贴应保留在线缆上；盘绕线缆时不要使用手肘绕线。
• 将麦克风安装到悬臂或麦克风架上之前，先连接 XLR 线缆。
• 所有设备附近禁止放置液体。

安装步骤

1. 准备讲台
图纸：1-1 座位布局图、4-1 舞台区域设备布局大比例图

• 首先： 协助扬声器组确认测量距离，包括扬声器位置、讲台位置、通道、座位区域和相关间距。
• 确认 SPK-4.1、SPK-4.2、SPK-5.1 和 SPK-5.2 的位置。
• 安装并按照讲台布置摆放讲台（lectern）。
• 移除旧的或容易分散注意力的胶带。
• 检查讲台表面和节目参与者行走路线是否有绊倒危险。
• 确认讲台布置符合图纸。
• 保持区域畅通，方便音频组和视频组工作。

2. 安装 SPK-4 和 SPK-5
图纸：4-1 舞台区域设备布局大比例图、6-3 讲台及部门扬声器接线图

• 从 PLS-1 取出 SPK-4.1 和 SPK-4.2。
• 从 ALS-4 取出 SPK-5.1 和 SPK-5.2。
• 按照图纸摆放四只扬声器。
• SPK-4.1 和 SPK-4.2 必须横向侧放。
• 按照图纸所示的位置和方向摆放 SPK-5.1 和 SPK-5.2。
• 在扬声器周围预留足够空间，以便安全连接线缆。

⚠️ 重要提示： SPK-4.1 和 SPK-4.2 是讲台监听扬声器，必须保持横向侧放。

3. 铺设、连接并保护讲台音频线缆
参考资料：CO-160a，第 3 章 — Audio Signal Cables (ASC-xx)，第 7–8 页
图纸：4-1 舞台区域设备布局大比例图、6-1 音频主控接线图、6-3 讲台及部门扬声器接线图

• 使用 ASC-01 XLR 音频线时，打开线缆原有的魔术贴，以滚开的方式展开线缆。不要把魔术贴从线缆上取下。
• MIC-1、MIC-2、MIC-3、MIC-4： 将 XLR 音频线从讲台麦克风铺设到 AMC-1。
• SPK-4.1 和 SPK-4.2： 铺设并连接 speakON 扬声器线缆。
• SPK-5.1 和 SPK-5.2： 铺设并连接 XLR 音频线缆。
• 与电源分配组协调 SPK-5.1 和 SPK-5.2 的电源连接。
• 在可行的情况下，避免 XLR 音频线与电源线直接平行铺设；需要交叉时，应以直角交叉。
• 沿讲台前缘整齐布设线缆，并避开节目参与者的行走路线。
• 根据需要使用少量胶带固定讲台上的线缆。
• 线缆穿过或进入通道时，使用适当的线缆保护装置。
• 确认每条线缆都连接到标签正确的麦克风或扬声器。

4. 标识并摆放麦克风
图纸：4-1 舞台区域设备布局大比例图、6-1 音频主控接线图

• 在每条有线麦克风线缆上贴上标签，注明对应的麦克风或用途。
• 在线缆连接 AMC-1 的一端贴一个标签，并在距离麦克风约 2 米的位置再贴一个标签。
• 将麦克风安装到悬臂或麦克风架上之前，先连接 XLR 线缆。
• 按照讲台布置和节目需要摆放讲台麦克风、主席麦克风和节目参与者麦克风。
• 电源分配组负责 WM-1 接收机设置、频率扫描和同步。
• WM-1 同步完成后，协调 MIC-5 和 MIC-6 在讲台上的摆放和使用。
• 与音频组协调进行最终麦克风和扬声器测试。

5. 标记节目参与者位置
图纸：4-1 舞台区域设备布局大比例图

• 标记采访、《守望台》评论以及相应麦克风架的位置。
• 标记要低调，但节目参与者和讲台服务员要看得清楚。

6. 确认讲台准备就绪

• 确认讲台时钟已经放在指定位置，并清晰可见。
• 将手提扩音器放在事先指定且容易拿取的位置。
• 与音频组确认 SPK-4、SPK-5 和所有麦克风已经完成测试。
• 确认所有讲台线缆已经固定，节目参与者的行走路线保持畅通。
• 确认讲台已经准备好进行走位练习。

完成检查表

• 已协助扬声器组完成测量
• 讲台布置及讲台（lectern）位置已确认
• 讲台及节目参与者通道没有绊倒危险
• SPK-4.1 和 SPK-4.2 已横向侧放
• SPK-5.1 和 SPK-5.2 已按照图纸摆放
• SPK-4 speakON 线缆已连接
• SPK-5 XLR 音频线缆已连接
• 已与电源分配组协调 SPK-5 电源
• MIC-1 至 MIC-4 XLR 音频线已铺设并加以保护
• 麦克风线缆已在 AMC-1 端及距麦克风约 2 米处贴上标签
• 音频线和电源线在可行的情况下已分开铺设
• 穿过通道的线缆已加以保护
• 有线麦克风已正确摆放
• 电源分配组完成 WM-1 设置及同步后，已协调无线麦克风的摆放
• 已与音频组测试 SPK-4、SPK-5 和麦克风
• 已标记节目参与者和麦克风架位置
• 讲台时钟和手提扩音器已放置到位
• 负责人已检查确认

拆卸

• 在星期日节目结束 30 分钟后，等待整个部门的简短会议和祷告后再开始拆卸。
• 小心移除胶带和线缆保护材料，并清理讲台区域。
• 将讲台组的所有设备、线缆、麦克风、麦克风架、扬声器、配件、讲台时钟和手提扩音器带到指定设备区域进行清点。
• 小心盘绕 ASC-01 XLR 音频线。不要使用手肘绕线，并使用线缆原有的魔术贴固定。
• 整齐盘绕其余线缆，避免扭曲、打结或急弯。
• 检查讲台区域是否遗留设备或材料。
• 负责人确认讲台组所有物品都已送到清点区域。

Related Pages / 相关页面

• Audio Cabling / 音频布线
• Loudspeakers / 扬声器
• Audio Booth (AHEC-1) / 音频控制台组
• Power Distribution / 电源分配