Skip to main content

Power Distribution and Intercom Setup / 电源分配与对讲系统安装

⚡ Power Distribution Team / 电源分配组

Team / 小组 Members / 成员
Power Distribution / 电源分配 • Jaturaphat (Dern) 🔑

🇬🇧 English Instructions

Purpose
This section provides the specific setup and dismantling instructions for the Power Distribution Team during the 2026 Bangkok Regional Convention. This team is responsible for routingRoute power to all A/V equipment, supporting installation ofinstall the intercom communication system, and settingset up the WM-1 wireless microphone system before final testingtesting.

by

⚠️ Safety & Installation Notes
• A qualified electrician must connect the Audiomain Crew.3-phase PDU (PDU-01) to the venue distribution board.
• Do not overload electrical circuits.
• Do not energize circuits until connections and breaker assignments have been confirmed.
• Protect power cables wherever they create a trip hazard.

Required References

  • Full Drawing Set: 📎 Complete PDF
  • Congregation Job Hazard Analysis (DC-85): 📁 Google Drive Folder
  • Wireless Microphone Setup:CO-160a: 📎 CO-160a,160a — Chapter 3 —3, Wireless Microphones (WM-1), pages 9–10
  • Specific Schematics:
    • 1-4 Power Distribution Layout Plan
    • 4-1 Stage Area Equipment Layout Large Scale View
    • 6-1 Audio Headend Wiring Diagram
    • 6-4 Intercom System Wiring Diagram
    • 6-6 Power Distribution Wiring Diagram
    • 6-7 Power Distribution Video Control Desk Wiring Diagram
    • 6-8 Audio Equipment Schedule
    • 6-9 Video and Power Equipment Schedule
    • 6-10 PDU Circuit Breaker Schedule
  • Event Content List: Cases PCS-1, PCS-3, IC-1/1, IC-1/2, WM-1

Required Equipment Cases

  • PCS-1: Contains powerPower distribution cables, sockets, 1-phase PDU, and tools.
  • PCS-3: Contains mainMain power equipment, 3-phase PDU (PDU-01), and cables.
  • IC-1/1: Contains the Ezicom Intercom Master Station (IMS-1).
  • IC-1/2: Contains the Ezicom beltpacks and headsets.
  • WM-1: Contains 1 SHURE SLXD4D dual wireless receiver and 2 SHURE BETA 58A handheld wireless microphones (MIC-5 and MIC-6).

💡 Priority / Operating Notes:
• Electrician Required: Use a qualified electrician to connect the main 3-phase PDU (PDU-01) to the venue distribution board in the corridor behind the stage.
• Do not overload electrical circuits.
• Use rubber cable protectors when crossing walkways and carpet covers under seating areas.

Setup Steps

1. PullRoute Power Cables to the A/V BoothsControl Area
Schematics: Pages 1-4 Power Distribution Layout Plan, 6-6 Power Distribution Wiring Diagram, 6-7 Power Distribution Video Control Desk Wiring Diagram

  • Pull power cables from the A/V control booths to the wall socket or main power supply.
Route power to the Video Booth, Audio Booth, and any required control-area equipment. DoFollow not connect orthe power ondistribution equipmentshown untilin the Powerschematics. Distribution Team confirms thatKeep power iscables ready.neat and protected as they are installed.
🗺️ View Associated Schematics (Pages 1-4, 6-6, 6-7)
1-4 Power Distribution Layout Plan showing PDU, UPS, and power distribution locations / 电源分配布局图，显示 PDU、UPS 及电源分配位置

6-6 Power Distribution Wiring Diagram showing PDU-01, power sockets, audio headend power, TVs, and LED wall power distribution / 电源分配接线图，显示 PDU-01、电源插座、音频主控供电、电视及 LED 屏幕电源分配

6-7 Power Distribution Video Control Desk Wiring Diagram showing UPS-01, VHEC-1, wireless receivers, intercom master unit, and video control desk power connections / 视频控制台电源接线图，显示 UPS-01、VHEC-1、无线接收器、对讲主机及视频控制台电源连接

2. PullSet Up Stage Power Cablesand to the StagePDU-01
Schematics: Pages 1-4 Power Distribution Layout Plan, 6-6 Power Distribution Wiring Diagram, 6-9 Video and Power Equipment Schedule, 6-10 PDU Circuit Breaker Schedule

  • PullRoute power cables from behindto the stage up onto the stage to supply power for stage A/V equipment and LED walls.
  • AHave a qualified electrician must connect PDU-01 to the venue distribution board.
  • Set up the PDU circuit breakers according to the schedule.
  • Confirm that the required power points are availableready before theequipment Audio,is Video, and LED teams begin final commissioning.energized.
🗺️ View Associated Schematics (Pages 1-4, 6-6, 6-9, 6-10)
1-4 Power Distribution Layout Plan showing PDU, UPS, and power distribution locations / 电源分配布局图，显示 PDU、UPS 及电源分配位置

6-6 Power Distribution Wiring Diagram showing PDU-01, power sockets, audio headend power, TVs, and LED wall power distribution / 电源分配接线图，显示 PDU-01、电源插座、音频主控供电、电视及 LED 屏幕电源分配

6-9 Video and Power Equipment Schedule listing video equipment, TVs, LED walls, PDU, UPS, cables, and power distribution equipment / 视频和电源设备清单，列出视频设备、电视、LED 屏幕、PDU、UPS、线缆及电源分配设备

6-10 PDU Circuit Breaker Schedule listing breaker loads for back row TVs, main video control desk, stage AV equipment, audio system, and LED walls / PDU 断路器清单，列出后排电视、主视频控制台、舞台影音设备、音频系统及 LED 屏幕的断路器负载

3. Install the Intercom System
Schematics: Page 6-4 Intercom System Wiring Diagram

  • Install the intercom system for the Video, Audio, and Stage crews.
Place the mainIntercom masterMaster stationStation (IMS-1) at the Video Booth. Route the connections forConnect the 2 stageStage headsetspositions and 1 audioAudio headsetBooth position according to the schematic. Confirm communication between the Video Booth, Audio Booth, and Stage positions.Stage.
🗺️ View Intercom System Schematic (Page 6-4)
6-4 Intercom System Wiring Diagram showing IMS-1 master unit, intercom belt packs, headsets, and cable connections / 对讲系统接线图，显示 IMS-1 主机、对讲腰包、耳机及线缆连接

4. Install and Configure WM-1 Wireless Microphones
Reference: 📎 CO-160a,160a — Chapter 3 —3, Wireless Microphones (WM-1), pages 9–10
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-1 Audio Headend Wiring Diagram, 6-8 Audio Equipment Schedule

  • Position and connect the WM-1 receiver according to the schematics. The event-specific WM-1 set contains 1 SHURE SLXD4D dual receiver and 2 BETA 58A handheld wireless microphones (MIC-5 and MIC-6).
  • Connect power to WM-1 and turn on the receiver.
  • On the receiver, selectSelect 1. Frequency Setup > 1.1 Guided Frequency Setup.
, Selectthen select Initialize My System and push the control knob to continue.. Turn off both transmitters (MIC-5 and MIC-6)6, beforethen scanning. Selectselect start scan. When the scan is complete, pushassign the control knob to assign frequencies to the receiver.frequencies. Turn on each transmittermicrophone one at a time.time, Alignalign the infraredIR (IR) ports on the transmitterports, and receiver, then press sync. Confirm that both MIC-5 and MIC-6 are synchronized. If manual frequency setup is required, use 1. Frequency Setup > 1.4 Manual Frequency Setup. Coordinate with the Audio Crew for final microphone signal and audio testing.
🗺️ View Associated Schematics (Pages 4-1, 6-1, 6-8)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

6-8 Audio Equipment Schedule listing microphones, wireless receivers, audio interfaces, intercom equipment, loudspeakers, and related audio equipment / 音频设备清单，列出麦克风、无线接收器、音频接口、对讲设备、扬声器及相关音频设备

5. Final Cable ManagementProtection

  • UseProtect rubbercables cablewherever protectorsthey whencross crossingor walkways.enter a walkway.
  • Use the appropriate cable protectors, rubber mats, or carpet coverscovers.
Keep cable routes neat and clearly identifiable. Check all routes for cablestrip runninghazards underbefore seating areas. Consider attaching a tag to each cable identifying its use if time permits. Note: When putting carpet covers down over walkways, tape one side only. Tapeenergizing the other side once the entire installation is finished.system.

Completion Checklist

  • MainPower 3-phaserouted PDUto connectedthe byA/V qualifiedcontrol electricianarea
  • CircuitQualified electrician connected PDU-01
 PDU circuit breakers set according to the schedule Power cables pulled toStage A/V booths  Power cables pulled to stage A/V equipment and LED wallswall power ready Intercom mastercommunication stationconfirmed placedbetween atVideo, Video Booth  StageAudio, and Audio Booth intercom headsets connectedStage WM-1 receiver positioned, connected, and powered Guided Frequency Setup completed MIC-5 and MIC-6 synchronized Audio Crew notified for final microphone signal and audioWM-1 testing WalkwayPower cables protected withand rubberroutes cable protectors  Seating-area cables protected with carpet coverssafe Keyman inspection completed

Dismantling Procedure

  • Wait for the department briefing and prayer 30 minutes after the program ends on Sunday before dismantling.
  • Carefully power down allthe equipment.
  • Turn off MIC-5 and MIC-6 and return them to the WM-1 case.1.
  • Disconnect WM-1, allintercom power cables,equipment, and intercompower cables.
  • Remove cable protectors and carpet coversprotection carefully.
  • Coil and label all cables.
  • Gather all equipment and bring it to the designated area.
  • Note for team leader: Use the Bill of Materials (BOM) to cross off every box or case before it is brought to the truck:
    • PCS-1
    • PCS-3
    • IC-1/1
    • IC-1/2
    • WM-1

🇨🇳 中文说明

目的
本页面提供 2026 年曼谷区域大会期间 电源分配组 的具体安装和拆卸说明。该小组负责为所有音视频设备布设电源、协助安装对讲通信系统，并在音频组进行最终测试前安装和设置为音视频设备布设电源、安装对讲系统，并设置 WM-1 无线麦克风系统。无线麦克风系统，为最终测试做好准备。

⚠️ 安全与安装提示
• 必须由合格的电工将主三相 PDU (PDU-01) 连接到场馆配电箱。
• 不要让电路过载。
• 确认所有连接和断路器设置正确后，才能接通电源。
• 电源线可能造成绊倒危险的位置必须加以保护。

参考资料

  • 完整图纸： 📎 完整 PDF 文件
  • 《会众工作危险性分析》(DC-85)： 📁 Google Drive 文件夹
  • WM-1 无线麦克风：CO-160a： 📎 CO-160a，160a — 第 3 章 — 章，Wireless Microphones (WM-1)，第 9–10 页
  • 相关图纸：
    • 1-4 电源分配布局图
    • 4-1 舞台区域设备布局大比例图
    • 6-1 音频主控接线图
    • 6-4 对讲系统接线图
    • 6-6 电源分配接线图
    • 6-7 视频控制台电源接线图
    • 6-8 音频设备清单
    • 6-9 视频和电源设备清单
    • 6-10 PDU 断路器清单
  • 大会设备清单： 设备箱 PCS-1, 1、PCS-3, 3、IC-1/1, 1、IC-1/2, 2、WM-1

所需设备箱

  • PCS-1： 包含电源分配线缆、电源分配线缆、插座、单相 PDU 和工具。
  • PCS-3： 包含主电源设备、主电源设备、三相 PDU (PDU-01) 和线缆。
  • IC-1/1： 包含 Ezicom 对讲系统主机 (IMS-1)。
  • IC-1/2： 包含 Ezicom 对讲系统腰包和耳机。
  • WM-1： 包含 1 台 SHURE SLXD4D 双通道无线接收机及 2 支 SHURE BETA 58A 手持无线麦克风（MIC-5 和 MIC-6）。

💡 优先事项 / 操作提示：
• 需要电工： 请安排合格的电工将主三相 PDU (PDU-01) 连接到讲台后方走廊的场馆配电箱（三相电源）。
• 不要让电路过载。
• 穿过过道时使用橡胶电缆盖板，座位区域下方使用地毯盖板。

安装步骤

1. 布置音视频控制台电源布置音视频控制区电源
图纸：1-4 电源分配布局图、6-6 电源分配接线图、6-7 视频控制台电源接线图

  • 将电源线从音视频控制台布置连接到墙壁插座或主电源。
为视频控制台、音频控制台及所需控制区设备布设电源。 在电源分配组确认电源准备好之前，不要连接或开启设备。按照图纸进行电源分配。 布线时保持电源线整齐并加以保护。
🗺️ 查看相关图纸（图纸 1-4, 6-6, 6-7）
1-4 Power Distribution Layout Plan showing PDU, UPS, and power distribution locations / 电源分配布局图，显示 PDU、UPS 及电源分配位置

6-6 Power Distribution Wiring Diagram showing PDU-01, power sockets, audio headend power, TVs, and LED wall power distribution / 电源分配接线图，显示 PDU-01、电源插座、音频主控供电、电视及 LED 屏幕电源分配

6-7 Power Distribution Video Control Desk Wiring Diagram showing UPS-01, VHEC-1, wireless receivers, intercom master unit, and video control desk power connections / 视频控制台电源接线图，显示 UPS-01、VHEC-1、无线接收器、对讲主机及视频控制台电源连接

2. 布置讲台电源安装讲台电源及 PDU-01
图纸：1-4 电源分配布局图、6-6 电源分配接线图、6-9 视频和电源设备清单、6-10 PDU 断路器清单

  • 将电源线从讲台后方的走廊拉到讲台上，为讲台音视频设备和 LED 屏幕供电。屏幕布设电源。
  • 必须由合格的电工将由合格的电工将 PDU-01 连接到场馆配电箱。
  • 根据清单设置按照清单设置 PDU 断路器。
  • 在音频组、视频组和 LED 组进行最后调试前，确认所需电源点已准备好。接通设备电源前，确认所有所需电源点已经准备好。
🗺️ 查看相关图纸（图纸 1-4, 6-6, 6-9, 6-10）
1-4 Power Distribution Layout Plan showing PDU, UPS, and power distribution locations / 电源分配布局图，显示 PDU、UPS 及电源分配位置

6-6 Power Distribution Wiring Diagram showing PDU-01, power sockets, audio headend power, TVs, and LED wall power distribution / 电源分配接线图，显示 PDU-01、电源插座、音频主控供电、电视及 LED 屏幕电源分配

6-9 Video and Power Equipment Schedule listing video equipment, TVs, LED walls, PDU, UPS, cables, and power distribution equipment / 视频和电源设备清单，列出视频设备、电视、LED 屏幕、PDU、UPS、线缆及电源分配设备

6-10 PDU Circuit Breaker Schedule listing breaker loads for back row TVs, main video control desk, stage AV equipment, audio system, and LED walls / PDU 断路器清单，列出后排电视、主视频控制台、舞台影音设备、音频系统及 LED 屏幕的断路器负载

3. 安装对讲系统
图纸：6-4 对讲系统接线图

  • 为视频组、音频组和讲台组安装对讲系统。
将对讲系统主机 (IMS-1) 放置在视频控制台。 根据图纸连接通往讲台的按照图纸连接讲台的 2 个耳机和音频控制台的个位置及音频控制台的 1 个耳机。个位置。 确认视频控制台、音频控制台和讲台位置之间通讯正常。音频控制台和讲台之间通讯正常。
🗺️ 查看对讲系统图纸（图纸 6-4）
6-4 Intercom System Wiring Diagram showing IMS-1 master unit, intercom belt packs, headsets, and cable connections / 对讲系统接线图，显示 IMS-1 主机、对讲腰包、耳机及线缆连接

4. 安装并设置 WM-1 无线麦克风系统
参考资料：📎 CO-160a，160a — 第 3 章 — 章，Wireless Microphones (WM-1)，第 9–10 页
图纸：4-1 舞台区域设备布局大比例图、6-1 音频主控接线图、6-8 音频设备清单

  • 按照图纸放置并连接 WM-1。本次大会的 WM-1 包含 1 台 SHURE SLXD4D 双通道接收机及 2 支 BETA 58A 手持无线麦克风（MIC-5 和 MIC-6）。接收机。
  • 连接 WM-1 电源，并开启接收机。连接电源并开启接收机。
  • 在接收机上选择选择 1. Frequency Setup > 1.1 Guided Frequency Setup。
选择，然后选择 Initialize My System，然后按下控制旋钮继续。。 扫描前关闭两个发射器（关闭 MIC-5 和 MIC-6）。 选择6，然后选择 start scan 扫描频率。。 扫描完成后，按下控制旋钮，为接收机分配频率。扫描完成后分配频率。 逐一开启发射器。 将每支发射器与接收机的红外（逐一开启麦克风，对准红外（IR）端口对准，端口，然后按 sync。 确认 MIC-5 和 MIC-6 均已成功同步。均已同步。 如果需要手动设置频率，如需手动设置，请使用 1. Frequency Setup > 1.4 Manual Frequency Setup。 完成后与音频组协调，由音频组进行最终麦克风信号和音频测试。与音频组协调进行最终麦克风信号和音频测试。
🗺️ 查看相关图纸（图纸 4-1, 6-1, 6-8）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

6-8 Audio Equipment Schedule listing microphones, wireless receivers, audio interfaces, intercom equipment, loudspeakers, and related audio equipment / 音频设备清单，列出麦克风、无线接收器、音频接口、对讲设备、扬声器及相关音频设备

5. 线缆管理最终线缆保护

  • 在穿过过道时使用橡胶电缆盖板。在线缆穿过或进入通道的位置加以保护。
  • 座位区域下方的线缆使用地毯盖板。根据需要使用电缆盖板、橡胶垫或地毯盖板。
  • 如果时间允许，请考虑为每根线缆贴上标签以标明其用途。保持线缆路线整齐并容易识别。
  • 注意： 在过道铺设地毯盖板时，只需先用胶带固定一侧。等整个安装完成后再用胶带固定另一侧。接通系统电源前，检查所有路线是否存在绊倒危险。

完成检查表

  • 合格电工已连接主三相 PDU电源已布设至音视频控制区
  •  合格电工已连接 PDU-01
 PDU 断路器已按清单设置 电源线已拉至音视频控制台讲台音视频设备和 LED 屏幕电源已准备好 电源线已拉至讲台音视频设备和 LED 屏幕  对讲主机已放置在视频控制台  讲台和音频控制台对讲耳机已连接视频、音频和讲台之间的对讲通讯已确认 WM-1 接收机已放置、连接并通电 Guided Frequency Setup 已完成 MIC-5 和 MIC-6 已同步 已通知音频组进行最终麦克风信号和音频测试已通知音频组进行 WM-1 最终测试 过道线缆已使用橡胶电缆盖板保护  座位区域线缆已使用地毯盖板保护电源线已妥善保护，路线安全 负责人已检查确认

拆卸步骤

  • 在星期日节目结束 30 分钟后，等待整个部门的简短会议和祷告后再开始拆除工作。
  • 小心关闭所有设备电源。小心关闭设备电源。
  • 关闭 MIC-5 和 MIC-6，并将它们放回并放回 WM-1 设备箱。1。
  • 断开 WM-1、所有电源线和对讲系统线缆。对讲设备和电源线。
  • 小心移除电缆盖板和地毯盖板。小心移除线缆保护材料。
  • 整理并标识所有线缆。整理并标识线缆。
  • 收集所有设备并带到指定区域。
  • 组长注意： 在将每个箱子或设备箱搬上卡车前，请使用物料清单 (BOM) 核对并划掉每一项：
    • PCS-1
    • PCS-3
    • IC-1/1
    • IC-1/2
    • WM-1