Skip to main content

Stage Layout Setup / 讲台布局安装

🎭 Stage Team / 讲台组

Crew Overseer / 小组监督: Liu Shan 刘善

Team / 小组 Members / 成员
Stage Setup / 讲台安装 • Tomohiro 木田智宏 🔑
• Ellie 艾莉

🇬🇧 English Instructions

Purpose
Prepare the stage area, install microphone cabling, mark participant positions, and secure all stage cables according to the schematics before audio testing and walk-throughs.

⚠️ Safety & Installation Notes
• Tape down and cover all cables.
• Do not leave loose cables where participants will walk.
• Keep liquids away from all equipment.
• Installation Note: When installing microphones on booms/stands, please have the XLR cable already connected.

Required References

Required Equipment Cases

  • MS-1: Contains 6 manual floor microphone stands with adjustable booms.
  • ASC-01: Contains XLR cables (5m, 10m, and 20m lengths).
  • WM-1: Contains wireless microphones (BETA 58A) and receivers.
  • Note: Wired lectern/participant microphones are stored inside the AHEC-1 case.

Setup Steps

1. Prepare the Stage
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • First: Assist the Loudspeakers Team with chair measurements, including speakers, stage, aisles, and related spacing.
  • Remove old or distracting tape from the stage.
  • Check the stage surface for trip hazards.
  • Confirm the stage layout follows the schematics.
  • Keep the area clear for Audio Crew and Video Crew work.
🗺️ View Associated Schematic (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

2. Pull XLR Cables for Microphones
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-1 Audio Headend Wiring Diagram

  • Route the microphone XLR cables to the audio multicore cable (AMC-1) for MIC-1, MIC-2, MIC-3, and MIC-4.
  • Pull XLR cables up onto the stage and fasten using small pieces of tape.
  • Route cables neatly along the front edge of the stage, away from participant walking paths.
  • Secure cables with tape as they are installed.
🗺️ View Associated Schematics (Pages 4-1, 6-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

3. Label Microphone Cables
Schematics: Page 6-1 Audio Headend Wiring Diagram

  • Attach a tag to each cable identifying its microphone assignment or use.
  • Place one tag at the audio multicore cable (AMC-1) end.
  • Place another tag approximately 2 meters from the microphone.
🗺️ View Audio Headend Wiring Diagram (Page 6-1)
6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

4. Position Microphones
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • Place microphones according to the stage layout and program needs.
  • Confirm lectern, chairman, and participant microphone positions.
  • Coordinate with the Audio Crew for testing.
🗺️ View Stage Area Equipment Layout (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

5. Mark Participant Positions
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • Put tape down where interviews, Watchtower comments, and their microphone stands should be placed.
  • Keep markings discreet but visible to participants.
🗺️ View Stage Area Equipment Layout (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

Completion Checklist

  • Assisted Loudspeakers Team with measurements
  • Stage surface cleared of trip hazards and old tape
  • XLR cables pulled, routed neatly, and taped down
  • All cables tagged at snake end and 2m from microphone
  • Microphones positioned correctly on stage
  • Participant and microphone stand positions marked with tape
  • Keyman inspection completed

Dismantling Procedure

  • Wait for the department briefing and prayer 30 minutes after the program ends on Sunday before dismantling.
  • Remove stage microphones and stands.
  • Disconnect XLR cables from microphones and snake cable.
  • Remove tape and carpet covers carefully.
  • Coil and label all cables.
  • Gather all stage equipment and bring it to the designated area.
  • Check the stage for forgotten tape, cables, microphones, or accessories.
  • Note for team leader: Use the Bill of Materials (BOM) to cross off every box or case before it is brought to the truck:
    • MS-1
    • ASC-01
    • WM-1

🇨🇳 中文说明

目的
根据图纸准备讲台区域、安装麦克风线缆、标记节目参与者位置，并固定所有讲台线缆，为音频测试和走位练习做好准备。

⚠️ 安全与安装提示
• 所有线缆都要用胶带固定并覆盖。
• 节目参与者行走的位置不要留下松散线缆。
• 所有设备附近禁止放置液体。
• 安装提示： 将麦克风安装到麦克风悬臂架上之前，请先连接好 XLR 线缆。

参考资料

所需设备箱

  • MS-1： 包含 6 个带可调节麦克风悬臂的落地麦克风架。
  • ASC-01： 包含 XLR 音频线缆（5 米、10 米和 20 米长度）。
  • WM-1： 包含无线麦克风 (BETA 58A) 和接收器。
  • 注意： 有线讲台/参与者麦克风存放在 AHEC-1 设备箱内。

安装步骤

1. 准备讲台
图纸：4-1 舞台区域设备布局图大比例图

  • 首先： 协助扬声器组确认椅子测量距离，包括扬声器、讲台、通道和相关间距。
  • 移除讲台上旧的或容易分散注意力的胶带。
  • 检查讲台表面是否有绊倒危险。
  • 确认讲台布置符合图纸。
  • 保持区域畅通，方便音频组和视频组工作。
🗺️ 查看相关图纸（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

2. 铺设麦克风 XLR 线缆
图纸：4-1 舞台区域设备布局图大比例图、6-1 音频主控接线图

  • 将 MIC-1、MIC-2、MIC-3 和 MIC-4 的麦克风 XLR 线缆铺设到音频多芯线缆（AMC-1）。
  • 将 XLR 线缆拉上讲台，并用少量胶带固定。
  • 沿讲台前缘整齐布设线缆，线缆应远离节目参与者的行走路线。
  • 安装过程中使用胶带固定线缆。
🗺️ 查看相关图纸（图纸 4-1, 6-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

3. 标识麦克风线缆
图纸：6-1 音频主控接线图

  • 在每条线缆上贴上标签，注明对应的麦克风或用途。
  • 在线缆连接音频多芯线缆（AMC-1）的那一端贴一个标签。
  • 在距离麦克风约 2 米的位置再贴另一个标签。
🗺️ 查看音频主控接线图（图纸 6-1）
6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

4. 摆放麦克风
图纸：4-1 舞台区域设备布局图大比例图

  • 按照讲台布置和节目需要摆放麦克风。
  • 确认讲台麦克风、主席麦克风和节目参与者麦克风位置。
  • 与音频组协调进行测试。
🗺️ 查看舞台区域设备布局图（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

5. 标记节目参与者位置
图纸：4-1 舞台区域设备布局图大比例图

  • 在采访人员、《守望台》评论员及其麦克风架应该摆放的位置贴上标记胶带。
  • 标记要低调，但节目参与者要看得清楚。
🗺️ 查看舞台区域设备布局图（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

完成检查表

  • 已协助扬声器组完成测量
  • 讲台表面已清理，无绊倒危险及旧胶带
  • XLR 线缆已铺设、整齐走线并用胶带固定
  • 所有线缆已贴标签（多芯线端及距麦克风 2 米处）
  • 麦克风已在讲台上正确摆放
  • 已用胶带标记节目参与者和麦克风架位置
  • 负责人已检查确认

拆卸步骤

  • 在星期日节目结束 30 分钟后，等待整个部门的简短会议和祷告后再开始拆除工作。
  • 拆下讲台麦克风和麦克风架。
  • 从麦克风和多芯音频线拆除 XLR 线缆。
  • 小心移除胶带和地毯覆盖物。
  • 整理并标识所有线缆。
  • 将所有讲台设备带到指定区域。
  • 检查讲台是否遗留胶带、线缆、麦克风或配件。
  • 组长注意： 在将每个箱子或设备箱搬上卡车前，请使用物料清单 (BOM) 核对并划掉每一项：
    • MS-1
    • ASC-01
    • WM-1