Skip to main content

Stage Layout Setup / 讲台布局安装

🎭 Stage Team / 讲台组

Crew Overseer / 小组监督: Liu Shan 刘善

Team / 小组 Members / 成员
Stage Setup / 讲台安装 • Tomohiro 木田智宏 🔑
• Ellie 艾莉

🇬🇧 English Instructions

Purpose
Prepare the stage area, install the SPK-4 and SPK-5 loudspeaker groups, route the stage audio cables, position the microphones, mark participant positions, and confirm that required stage equipment is ready before audio testing and walk-throughs.

⚠️ Safety & Installation Notes
• Tape down and cover all cables.
• Do not leave loose cables where participants will walk.
• Keep liquids away from all equipment.
• Microphone Installation: When installing microphones on booms or stands, have the XLR cable already connected.

Required References

  • Full Drawing Set: 📎 Complete PDF
  • Event Content List: Cases MS-1, ASC-01, WM-1, PLS-1 (SPK-4.1 and SPK-4.2), and ALS-4

Required Equipment Cases

  • MS-1: Contains 6 manual floor microphone stands with adjustable booms.
  • ASC-01: Contains XLR cables in 5 m, 10 m, and 20 m lengths.
  • WM-1: Contains wireless microphones (BETA 58A) and receivers.
  • PLS-1: SPK-4.1 and SPK-4.2 are stored in this case. The Stage Team is responsible for these two stage monitor loudspeakers.
  • ALS-4: Contains the SPK-5.1 and SPK-5.2 loudspeaker group.
  • Note: Wired lectern and participant microphones are stored inside the AHEC-1 case.
  • Local Equipment: Stage clock and megaphone.

Setup Steps

1. Prepare the Stage
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • First: Assist the Loudspeakers Team with chair measurements, including loudspeaker positions, the stage, aisles, seating sections, and related spacing.
  • Confirm the positions of SPK-4.1, SPK-4.2, SPK-5.1, and SPK-5.2.
  • Remove old or distracting tape from the stage.
  • Check the stage surface for trip hazards.
  • Confirm the stage layout follows the schematics.
  • Keep the area clear for Audio Crew and Video Crew work.
🗺️ View Associated Schematic (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

2. Install the SPK-4 and SPK-5 Loudspeaker Groups
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View and 6-3 Audio Loudspeaker Wiring Diagram

  • Retrieve SPK-4.1 and SPK-4.2 from the PLS-1 case.
  • Retrieve SPK-5.1 and SPK-5.2 from the ALS-4 case.
  • Position all four loudspeakers according to the schematics.
  • Place SPK-4.1 and SPK-4.2 horizontally on their sides.
  • Position SPK-5.1 and SPK-5.2 according to the locations and orientation shown in the schematics.
  • Leave enough space around the loudspeakers for the cables to be connected safely.

⚠️ Important: SPK-4.1 and SPK-4.2 are stage monitor loudspeakers and must remain horizontally positioned on their sides.

🗺️ View Loudspeaker Placement Schematic (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing the positions of SPK-4 and SPK-5 loudspeakers / 舞台区域设备布局大比例图，显示 SPK-4 和 SPK-5 扬声器的位置

For SPK-4 and SPK-5 wiring, refer to Page 6-3 Audio Loudspeaker Wiring Diagram in the complete drawing set.

3. Route and Connect the Stage Audio Cables
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-1 Audio Headend Wiring Diagram, and 6-3 Audio Loudspeaker Wiring Diagram

Route the following cables according to the schematics:

  • MIC-1, MIC-2, MIC-3, and MIC-4: Route XLR microphone cables from the stage microphones to the audio multicore cable (AMC-1).
  • SPK-4.1 and SPK-4.2: Route and connect speakON loudspeaker cables to the two stage monitor loudspeakers.
  • SPK-5.1 and SPK-5.2: Route and connect XLR audio cables to the two SPK-5 loudspeakers.
  • Coordinate with the Power Team for the power connections required by SPK-5.1 and SPK-5.2.
  • Route cables neatly along the front edge of the stage and away from participant walking paths.
  • Pull the required cables up onto the stage and secure them using small pieces of tape.
  • Protect and cover all cables that cross or run near a walkway.
  • Confirm that every cable is connected to the correctly labeled microphone or loudspeaker.
🗺️ View Associated Schematics (Pages 4-1 and 6-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

For the speakON and XLR loudspeaker connections, refer to Page 6-3 Audio Loudspeaker Wiring Diagram in the complete drawing set.

4. Label Microphone Cables
Schematics: Page 6-1 Audio Headend Wiring Diagram

  • Attach a tag to each microphone cable identifying its microphone assignment or use.
  • Place one tag at the audio multicore cable (AMC-1) end.
  • Place another tag approximately 2 meters from the microphone.
🗺️ View Audio Headend Wiring Diagram (Page 6-1)
6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

5. Position Microphones
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • Place microphones according to the stage layout and program needs.
  • Confirm the lectern, chairman, and participant microphone positions.
  • Coordinate with the Audio Crew for microphone and loudspeaker testing.
🗺️ View Stage Area Equipment Layout (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6. Mark Participant Positions
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • Put tape down where interviews, Watchtower comments, and their microphone stands should be placed.
  • Keep markings discreet but clearly visible to participants and stage attendants.
🗺️ View Stage Area Equipment Layout (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

7. Confirm the Stage Clock and Megaphone

  • Confirm that the clock is present on the stage and placed in its designated position.
  • Confirm that the clock is clearly visible to those who need to use it.
  • Confirm that the megaphone is in an agreed, easily accessible location.
  • Make sure the megaphone can be retrieved quickly if it is needed.

Completion Checklist

  • Assisted the Loudspeakers Team with measurements
  • Stage surface cleared of trip hazards and old tape
  • SPK-4.1 and SPK-4.2 positioned horizontally on their sides
  • SPK-5.1 and SPK-5.2 positioned according to the schematics
  • speakON cables routed and connected to SPK-4.1 and SPK-4.2
  • XLR audio cables routed and connected to SPK-5.1 and SPK-5.2
  • Power Team coordinated with for SPK-5 power connections
  • XLR microphone cables routed neatly and taped down
  • All microphone cables tagged at the AMC-1 end and 2 m from the microphone
  • Microphones positioned correctly on stage
  • SPK-4, SPK-5, and microphones tested with the Audio Crew
  • Participant and microphone stand positions marked with tape
  • Stage clock present and visible
  • Megaphone placed in an accessible location
  • Keyman inspection completed

Dismantling Procedure

  • Wait for the department briefing and prayer 30 minutes after the program ends on Sunday before dismantling.
  • Confirm with the Power Team before disconnecting or moving SPK-5.1 and SPK-5.2.
  • Disconnect the speakON cables from SPK-4.1 and SPK-4.2.
  • Disconnect the XLR audio cables from SPK-5.1 and SPK-5.2.
  • Bring SPK-4.1 and SPK-4.2 to the designated PLS-1 equipment area.
  • Bring SPK-5.1 and SPK-5.2 to the designated ALS-4 equipment area.
  • Remove stage microphones and stands.
  • Disconnect the XLR microphone cables from the microphones and the audio multicore cable (AMC-1).
  • Remove tape and carpet covers carefully.
  • Coil and label all cables.
  • Return the stage clock and megaphone to their designated storage location.
  • Gather all remaining stage equipment and bring it to the designated area.
  • Check the stage for forgotten tape, cables, microphones, loudspeakers, or accessories.
  • Note for team leader: Use the Bill of Materials (BOM) to cross off every Stage Team box or case before it is brought to the truck:
    • MS-1
    • ASC-01
    • WM-1
    • ALS-4

🇨🇳 中文说明

目的
按照图纸准备讲台区域，安装 SPK-4 和 SPK-5 扬声器组，铺设讲台音频线缆，摆放麦克风，标记节目参与者位置，并确认所需的讲台设备已准备就绪，为音频测试和走位练习做好准备。

⚠️ 安全与安装提示
• 所有线缆都要用胶带固定并覆盖。
• 节目参与者行走的位置不要留下松散线缆。
• 所有设备附近禁止放置液体。
• 麦克风安装提示： 将麦克风安装到麦克风悬臂架或麦克风架上之前，请先连接好 XLR 线缆。

参考资料

  • 完整图纸： 📎 完整 PDF 文件
  • 大会设备清单： 设备箱 MS-1、ASC-01、WM-1、PLS-1（SPK-4.1 和 SPK-4.2）及 ALS-4

所需设备箱

  • MS-1： 包含 6 个带可调节麦克风悬臂的落地麦克风架。
  • ASC-01： 包含 5 米、10 米和 20 米长度的 XLR 音频线缆。
  • WM-1： 包含无线麦克风（BETA 58A）和接收器。
  • PLS-1： SPK-4.1 和 SPK-4.2 存放在这个设备箱内。讲台组负责安装这两只讲台监听扬声器。
  • ALS-4： 包含 SPK-5.1 和 SPK-5.2 扬声器组。
  • 注意： 有线讲台麦克风和节目参与者麦克风存放在 AHEC-1 设备箱内。
  • 本地设备： 讲台时钟和手提扩音器。

安装步骤

1. 准备讲台
图纸：4-1 舞台区域设备布局图（大比例图）

  • 首先： 协助扬声器组确认测量距离，包括扬声器位置、讲台、通道、座位区域和相关间距。
  • 确认 SPK-4.1、SPK-4.2、SPK-5.1 和 SPK-5.2 的摆放位置。
  • 移除讲台上旧的或容易分散注意力的胶带。
  • 检查讲台表面是否有绊倒危险。
  • 确认讲台布置符合图纸。
  • 保持区域畅通，方便音频组和视频组工作。
🗺️ 查看相关图纸（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

2. 安装 SPK-4 和 SPK-5 扬声器组
图纸：4-1 舞台区域设备布局图（大比例图）和 6-3 讲台及部门扬声器接线图

  • 从 PLS-1 设备箱取出 SPK-4.1 和 SPK-4.2。
  • 从 ALS-4 设备箱取出 SPK-5.1 和 SPK-5.2。
  • 按照图纸摆放四只扬声器。
  • SPK-4.1 和 SPK-4.2 必须横向侧放。
  • 按照图纸所示的位置和方向摆放 SPK-5.1 和 SPK-5.2。
  • 在扬声器周围留出足够空间，以便安全连接线缆。

⚠️ 重要提示： SPK-4.1 和 SPK-4.2 是讲台监听扬声器，必须保持横向侧放。

🗺️ 查看扬声器摆放图纸（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing the positions of SPK-4 and SPK-5 loudspeakers / 舞台区域设备布局大比例图，显示 SPK-4 和 SPK-5 扬声器的位置

有关 SPK-4 和 SPK-5 的接线方法，请参阅完整图纸中的 6-3 讲台及部门扬声器接线图。

3. 铺设并连接讲台音频线缆
图纸：4-1 舞台区域设备布局图（大比例图）、6-1 音频主控接线图和 6-3 讲台及部门扬声器接线图

按照图纸铺设以下线缆：

  • MIC-1、MIC-2、MIC-3 和 MIC-4： 将麦克风 XLR 音频线从讲台麦克风铺设到音频多芯线缆（AMC-1）。
  • SPK-4.1 和 SPK-4.2： 将 speakON 扬声器线缆铺设并连接到两只讲台监听扬声器。
  • SPK-5.1 和 SPK-5.2： 将 XLR 音频线缆铺设并连接到两只 SPK-5 扬声器。
  • 与电源组协调 SPK-5.1 和 SPK-5.2 所需的电源连接。
  • 沿讲台前缘整齐布设线缆，并避开节目参与者的行走路线。
  • 将所需线缆拉上讲台，并用少量胶带固定。
  • 所有穿过通道或靠近通道的线缆都必须加以覆盖和保护。
  • 确认每条线缆都连接到标签正确的麦克风或扬声器。
🗺️ 查看相关图纸（图纸 4-1 和 6-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

有关 speakON 和 XLR 扬声器线缆的连接方法，请参阅完整图纸中的 6-3 讲台及部门扬声器接线图。

4. 标识麦克风线缆
图纸：6-1 音频主控接线图

  • 在每条麦克风线缆上贴上标签，注明对应的麦克风或用途。
  • 在线缆连接音频多芯线缆（AMC-1）的那一端贴一个标签。
  • 在距离麦克风约 2 米的位置再贴另一个标签。
🗺️ 查看音频主控接线图（图纸 6-1）
6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

5. 摆放麦克风
图纸：4-1 舞台区域设备布局图（大比例图）

  • 按照讲台布置和节目需要摆放麦克风。
  • 确认讲台麦克风、主席麦克风和节目参与者麦克风的位置。
  • 与音频组协调进行麦克风和扬声器测试。
🗺️ 查看舞台区域设备布局图（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6. 标记节目参与者位置
图纸：4-1 舞台区域设备布局图（大比例图）

  • 在采访人员、《守望台》评论员及其麦克风架应该摆放的位置贴上标记胶带。
  • 标记要低调，但节目参与者和讲台服务员要看得清楚。
🗺️ 查看舞台区域设备布局图（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

7. 确认讲台时钟和手提扩音器

  • 确认讲台时钟已经放在讲台上的指定位置。
  • 确认需要使用时钟的人员可以清楚看到。
  • 确认手提扩音器放在事先指定且容易拿取的位置。
  • 确保需要时可以迅速取用手提扩音器。

完成检查表

  • 已协助扬声器组完成测量
  • 讲台表面已清理，无绊倒危险及旧胶带
  • SPK-4.1 和 SPK-4.2 已横向侧放
  • SPK-5.1 和 SPK-5.2 已按照图纸摆放
  • speakON 线缆已铺设并连接到 SPK-4.1 和 SPK-4.2
  • XLR 音频线缆已铺设并连接到 SPK-5.1 和 SPK-5.2
  • 已与电源组协调 SPK-5 的电源连接
  • 麦克风 XLR 音频线已整齐铺设并用胶带固定
  • 所有麦克风线缆已贴标签（AMC-1 端及距麦克风 2 米处）
  • 麦克风已在讲台上正确摆放
  • 已与音频组测试 SPK-4、SPK-5 和麦克风
  • 已用胶带标记节目参与者和麦克风架位置
  • 讲台时钟已经放置并清晰可见
  • 手提扩音器已放在容易拿取的位置
  • 负责人已检查确认

拆卸步骤

  • 在星期日节目结束 30 分钟后，等待整个部门的简短会议和祷告后再开始拆除工作。
  • 在断开或移动 SPK-5.1 和 SPK-5.2 前，先与电源组确认。
  • 断开 SPK-4.1 和 SPK-4.2 的 speakON 扬声器线缆。
  • 断开 SPK-5.1 和 SPK-5.2 的 XLR 音频线缆。
  • 将 SPK-4.1 和 SPK-4.2 带到指定的 PLS-1 设备集合区域。
  • 将 SPK-5.1 和 SPK-5.2 带到指定的 ALS-4 设备集合区域。
  • 拆下讲台麦克风和麦克风架。
  • 从麦克风和音频多芯线缆（AMC-1）断开麦克风 XLR 音频线。
  • 小心移除胶带和地毯覆盖物。
  • 整理并标识所有线缆。
  • 将讲台时钟和手提扩音器放回指定的存放位置。
  • 将其余讲台设备带到指定区域。
  • 检查讲台是否遗留胶带、线缆、麦克风、扬声器或配件。
  • 组长注意： 在将每个讲台组的箱子或设备箱搬上卡车前，请使用物料清单（BOM）核对并划掉每一项：
    • MS-1
    • ASC-01
    • WM-1
    • ALS-4