Skip to main content

Stage Layout Setup / 讲台布局安装

🎭 Stage Team / 讲台组

Crew Overseer / 小组监督: Liu Shan 刘善

Team / 小组
Stage Setup / 讲台安装 • Tomohiro 木田智宏 🔑

🇬🇧 English Instructions

Purpose
Prepare the stage area, install the SPK-4 and SPK-5 loudspeaker groups, route the stage audio cables, position the microphones, mark participant positions, and confirm that required stage equipment is ready before audio testing and walk-throughs.

⚠️ Safety & Installation Notes
• Tape down and cover all cables.
• Do not leave loose cables where participants will walk.
• Keep liquids away from all equipment.
• Microphone Installation: When installing microphones on booms or stands, have the XLR cable already connected.

Required References

Event Content List: Cases MS-1, ASC-01, WM-1, PLS-1 (SPK-4.1 and SPK-4.2), and ALS-4

Required Equipment Cases

  • MS-1: Contains 6 manual floor microphone stands with adjustable booms.
  • ASC-01: Contains XLR cables in 5 m, 10 m, and 20 m lengths.
  • WM-1: Contains wireless microphones (BETA 58A) and receivers.receiver. Coordinate with the Power Distribution Team, which will assist with installation and configuration of the wireless microphone system.
  • PLS-1: SPK-4.1 and SPK-4.2 are stored in this case. The Stage Team is responsible for these two stage monitor loudspeakers.
  • ALS-4: Contains the SPK-5.1 and SPK-5.2 loudspeaker group.
  • Note: Wired lectern and participant microphones are stored inside the AHEC-1 case.
  • Local Equipment: Stage clock and megaphone.

Setup Steps

1. Prepare the Stage
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • First: Assist the Loudspeakers Team with chair measurements, including loudspeaker positions, the stage, aisles, seating sections, and related spacing.
  • Confirm the positions of SPK-4.1, SPK-4.2, SPK-5.1, and SPK-5.2.
  • Remove old or distracting tape from the stage.
  • Check the stage surface for trip hazards.
  • Confirm the stage layout follows the schematics.
  • Keep the area clear for Audio Crew and Video Crew work.
🗺️ View Associated Schematic (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

2. Install the SPK-4 and SPK-5 Loudspeaker Groups
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View and 6-3 Audio Loudspeaker Wiring Diagram

  • Retrieve SPK-4.1 and SPK-4.2 from the PLS-1 case.
  • Retrieve SPK-5.1 and SPK-5.2 from the ALS-4 case.
  • Position all four loudspeakers according to the schematics.
  • Place SPK-4.1 and SPK-4.2 horizontally on their sides.
  • Position SPK-5.1 and SPK-5.2 according to the locations and orientation shown in the schematics.
  • Leave enough space around the loudspeakers for the cables to be connected safely.

⚠️ Important: SPK-4.1 and SPK-4.2 are stage monitor loudspeakers and must remain horizontally positioned on their sides.

🗺️ View Loudspeaker Placement Schematic (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing the positions of SPK-4 and SPK-5 loudspeakers / 舞台区域设备布局大比例图，显示 SPK-4 和 SPK-5 扬声器的位置

For SPK-4 and SPK-5 wiring, refer to Page 6-3 Audio Loudspeaker Wiring Diagram in the complete drawing set.

3. Route and Connect the Stage Audio Cables
Schematics: Pages 4-1 Stage Area Equipment Layout Large Scale View, 6-1 Audio Headend Wiring Diagram, and 6-3 Audio Loudspeaker Wiring Diagram

Route the following cables according to the schematics:

  • MIC-1, MIC-2, MIC-3, and MIC-4: Route XLR microphone cables from the stage microphones to the audio multicore cable (AMC-1).
  • SPK-4.1 and SPK-4.2: Route and connect speakON loudspeaker cables to the two stage monitor loudspeakers.
  • SPK-5.1 and SPK-5.2: Route and connect XLR audio cables to the two SPK-5 loudspeakers.
  • Coordinate with the Power Distribution Team for the power connections required by SPK-5.1 and SPK-5.2.
  • Route cables neatly along the front edge of the stage and away from participant walking paths.
  • Pull the required cables up onto the stage and secure them using small pieces of tape.
  • Protect and cover all cables that cross or run near a walkway.
  • Confirm that every cable is connected to the correctly labeled microphone or loudspeaker.
🗺️ View Associated Schematics (Pages 4-1 and 6-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

For the speakON and XLR loudspeaker connections, refer to Page 6-3 Audio Loudspeaker Wiring Diagram in the complete drawing set.

4. Label Microphone Cables
Schematics: Page 6-1 Audio Headend Wiring Diagram

  • Attach a tag to each microphone cable identifying its microphone assignment or use.
  • Place one tag at the audio multicore cable (AMC-1) end.
  • Place another tag approximately 2 meters from the microphone.
🗺️ View Audio Headend Wiring Diagram (Page 6-1)
6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

5. Position Microphones
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • Place microphones according to the stage layout and program needs.
  • Confirm the lectern, chairman, and participant microphone positions.
  • Coordinate with the Power Distribution Team for installation and configuration of the WM-1 wireless microphone system.
Once WM-1 setup is complete, confirm that the wireless microphones are available in the required stage positions. Coordinate with the Audio Crew for final microphone and loudspeaker testing.
🗺️ View Stage Area Equipment Layout (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6. Mark Participant Positions
Schematics: Page 4-1 Stage Area Equipment Layout Large Scale View

  • Put tape down where interviews, Watchtower comments, and their microphone stands should be placed.
  • Keep markings discreet but clearly visible to participants and stage attendants.
🗺️ View Stage Area Equipment Layout (Page 4-1)
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

7. Confirm the Stage Clock and Megaphone

  • Confirm that the clock is present on the stage and placed in its designated position.
  • Confirm that the clock is clearly visible to those who need to use it.
  • Confirm that the megaphone is in an agreed, easily accessible location.
  • Make sure the megaphone can be retrieved quickly if it is needed.

Completion Checklist

  • Assisted the Loudspeakers Team with measurements
  • Stage surface cleared of trip hazards and old tape
  • SPK-4.1 and SPK-4.2 positioned horizontally on their sides
  • SPK-5.1 and SPK-5.2 positioned according to the schematics
  • speakON cables routed and connected to SPK-4.1 and SPK-4.2
  • XLR audio cables routed and connected to SPK-5.1 and SPK-5.2
  • Power Distribution Team coordinated with for SPK-5 power connections
  • XLR microphone cables routed neatly and taped down
  • All microphone cables tagged at the AMC-1 end and 2 m from the microphone
  • Microphones positioned correctly on stage
 WM-1 installation coordinated with the Power Distribution Team  Wireless microphones positioned as required for stage use SPK-4, SPK-5, and microphones tested with the Audio Crew Participant and microphone stand positions marked with tape Stage clock present and visible Megaphone placed in an accessible location Keyman inspection completed

Dismantling Procedure

  • Wait for the department briefing and prayer 30 minutes after the program ends on Sunday before dismantling.
  • Confirm with the Power Distribution Team before disconnecting or moving SPK-5.1 and SPK-5.2.
 Coordinate with the Power Distribution Team before disconnecting or packing the WM-1 wireless microphone system. Disconnect the speakON cables from SPK-4.1 and SPK-4.2. Disconnect the XLR audio cables from SPK-5.1 and SPK-5.2. Bring SPK-4.1 and SPK-4.2 to the designated PLS-1 equipment area. Bring SPK-5.1 and SPK-5.2 to the designated ALS-4 equipment area. Remove stage microphones and stands. Disconnect the XLR microphone cables from the microphones and the audio multicore cable (AMC-1). Remove tape and carpet covers carefully. Coil and label all cables. Return the stage clock and megaphone to their designated storage location. Gather all remaining stage equipment and bring it to the designated area. Check the stage for forgotten tape, cables, microphones, loudspeakers, or accessories. Note for team leader: Use the Bill of Materials (BOM) to cross off every Stage Team box or case before it is brought to the truck:
  • MS-1
  • ASC-01
  • WM-1
  • ALS-4

🇨🇳 中文说明

目的
按照图纸准备讲台区域，安装 SPK-4 和 SPK-5 扬声器组，铺设讲台音频线缆，摆放麦克风，标记节目参与者位置，并确认所需的讲台设备已准备就绪，为音频测试和走位练习做好准备。

⚠️ 安全与安装提示
• 所有线缆都要用胶带固定并覆盖。
• 节目参与者行走的位置不要留下松散线缆。
• 所有设备附近禁止放置液体。
• 麦克风安装提示： 将麦克风安装到麦克风悬臂架或麦克风架上之前，请先连接好 XLR 线缆。

参考资料

大会设备清单： 设备箱 MS-1、ASC-01、WM-1、PLS-1（SPK-4.1 和 SPK-4.2）及 ALS-4

所需设备箱

  • MS-1： 包含 6 个带可调节麦克风悬臂的落地麦克风架。
  • ASC-01： 包含 5 米、10 米和 20 米长度的 XLR 音频线缆。
  • WM-1： 包含无线麦克风（BETA 58A）和接收器。请与电源分配组协调，由电源分配组协助安装和设置无线麦克风系统。
  • PLS-1： SPK-4.1 和 SPK-4.2 存放在这个设备箱内。讲台组负责安装这两只讲台监听扬声器。
  • ALS-4： 包含 SPK-5.1 和 SPK-5.2 扬声器组。
  • 注意： 有线讲台麦克风和节目参与者麦克风存放在 AHEC-1 设备箱内。
  • 本地设备： 讲台时钟和手提扩音器。

安装步骤

1. 准备讲台
图纸：4-1 舞台区域设备布局图（大比例图）

  • 首先： 协助扬声器组确认测量距离，包括扬声器位置、讲台、通道、座位区域和相关间距。
  • 确认 SPK-4.1、SPK-4.2、SPK-5.1 和 SPK-5.2 的摆放位置。
  • 移除讲台上旧的或容易分散注意力的胶带。
  • 检查讲台表面是否有绊倒危险。
  • 确认讲台布置符合图纸。
  • 保持区域畅通，方便音频组和视频组工作。
🗺️ 查看相关图纸（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

2. 安装 SPK-4 和 SPK-5 扬声器组
图纸：4-1 舞台区域设备布局图（大比例图）和 6-3 讲台及部门扬声器接线图

  • 从 PLS-1 设备箱取出 SPK-4.1 和 SPK-4.2。
  • 从 ALS-4 设备箱取出 SPK-5.1 和 SPK-5.2。
  • 按照图纸摆放四只扬声器。
  • SPK-4.1 和 SPK-4.2 必须横向侧放。
  • 按照图纸所示的位置和方向摆放 SPK-5.1 和 SPK-5.2。
  • 在扬声器周围留出足够空间，以便安全连接线缆。

⚠️ 重要提示： SPK-4.1 和 SPK-4.2 是讲台监听扬声器，必须保持横向侧放。

🗺️ 查看扬声器摆放图纸（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing the positions of SPK-4 and SPK-5 loudspeakers / 舞台区域设备布局大比例图，显示 SPK-4 和 SPK-5 扬声器的位置

有关 SPK-4 和 SPK-5 的接线方法，请参阅完整图纸中的 6-3 讲台及部门扬声器接线图。

3. 铺设并连接讲台音频线缆
图纸：4-1 舞台区域设备布局图（大比例图）、6-1 音频主控接线图和 6-3 讲台及部门扬声器接线图

按照图纸铺设以下线缆：

  • MIC-1、MIC-2、MIC-3 和 MIC-4： 将麦克风 XLR 音频线从讲台麦克风铺设到音频多芯线缆（AMC-1）。
  • SPK-4.1 和 SPK-4.2： 将 speakON 扬声器线缆铺设并连接到两只讲台监听扬声器。
  • SPK-5.1 和 SPK-5.2： 将 XLR 音频线缆铺设并连接到两只 SPK-5 扬声器。
  • 与电源组协调与电源分配组协调 SPK-5.1 和 SPK-5.2 所需的电源连接。
  • 沿讲台前缘整齐布设线缆，并避开节目参与者的行走路线。
  • 将所需线缆拉上讲台，并用少量胶带固定。
  • 所有穿过通道或靠近通道的线缆都必须加以覆盖和保护。
  • 确认每条线缆都连接到标签正确的麦克风或扬声器。
🗺️ 查看相关图纸（图纸 4-1 和 6-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

有关 speakON 和 XLR 扬声器线缆的连接方法，请参阅完整图纸中的 6-3 讲台及部门扬声器接线图。

4. 标识麦克风线缆
图纸：6-1 音频主控接线图

  • 在每条麦克风线缆上贴上标签，注明对应的麦克风或用途。
  • 在线缆连接音频多芯线缆（AMC-1）的那一端贴一个标签。
  • 在距离麦克风约 2 米的位置再贴另一个标签。
🗺️ 查看音频主控接线图（图纸 6-1）
6-1 Audio Headend Wiring Diagram showing microphones, wireless receivers, audio interfaces, audio multicore cable, and AHEC-1 connections / 音频主控接线图，显示麦克风、无线接收器、音频接口、多芯音频线及 AHEC-1 接线

5. 摆放麦克风
图纸：4-1 舞台区域设备布局图（大比例图）

  • 按照讲台布置和节目需要摆放麦克风。
  • 确认讲台麦克风、主席麦克风和节目参与者麦克风的位置。
  • 与音频组协调进行麦克风和扬声器测试。与电源分配组协调安装和设置 WM-1 无线麦克风系统。
WM-1 设置完成后，确认无线麦克风已放在讲台所需的位置。 与音频组协调进行最终麦克风和扬声器测试。
🗺️ 查看舞台区域设备布局图（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

6. 标记节目参与者位置
图纸：4-1 舞台区域设备布局图（大比例图）

  • 在采访人员、《守望台》评论员及其麦克风架应该摆放的位置贴上标记胶带。
  • 标记要低调，但节目参与者和讲台服务员要看得清楚。
🗺️ 查看舞台区域设备布局图（图纸 4-1）
4-1 Stage Area Equipment Layout Large Scale View showing microphones, speakers, monitors, LED walls, and power distribution around the stage / 舞台区域设备布局大比例图，显示麦克风、扬声器、显示器、LED 屏幕及舞台电源分配

7. 确认讲台时钟和手提扩音器

  • 确认讲台时钟已经放在讲台上的指定位置。
  • 确认需要使用时钟的人员可以清楚看到。
  • 确认手提扩音器放在事先指定且容易拿取的位置。
  • 确保需要时可以迅速取用手提扩音器。

完成检查表

  • 已协助扬声器组完成测量
  • 讲台表面已清理，无绊倒危险及旧胶带
  • SPK-4.1 和 SPK-4.2 已横向侧放
  • SPK-5.1 和 SPK-5.2 已按照图纸摆放
  • speakON 线缆已铺设并连接到 SPK-4.1 和 SPK-4.2
  • XLR 音频线缆已铺设并连接到 SPK-5.1 和 SPK-5.2
  • 已与电源组协调已与电源分配组协调 SPK-5 的电源连接
  • 麦克风 XLR 音频线已整齐铺设并用胶带固定
  • 所有麦克风线缆已贴标签（AMC-1 端及距麦克风 2 米处）
  • 麦克风已在讲台上正确摆放
 已与电源分配组协调 WM-1 的安装  无线麦克风已放在讲台所需的位置 已与音频组测试 SPK-4、SPK-5 和麦克风 已用胶带标记节目参与者和麦克风架位置 讲台时钟已经放置并清晰可见 手提扩音器已放在容易拿取的位置 负责人已检查确认

拆卸步骤

  • 在星期日节目结束 30 分钟后，等待整个部门的简短会议和祷告后再开始拆除工作。
  • 在断开或移动 SPK-5.1 和 SPK-5.2 前，先与电源组确认。先与电源分配组确认。
 在断开或装箱 WM-1 无线麦克风系统前，先与电源分配组协调。 断开 SPK-4.1 和 SPK-4.2 的 speakON 扬声器线缆。 断开 SPK-5.1 和 SPK-5.2 的 XLR 音频线缆。 将 SPK-4.1 和 SPK-4.2 带到指定的 PLS-1 设备集合区域。 将 SPK-5.1 和 SPK-5.2 带到指定的 ALS-4 设备集合区域。 拆下讲台麦克风和麦克风架。 从麦克风和音频多芯线缆（AMC-1）断开麦克风 XLR 音频线。 小心移除胶带和地毯覆盖物。 整理并标识所有线缆。 将讲台时钟和手提扩音器放回指定的存放位置。 将其余讲台设备带到指定区域。 检查讲台是否遗留胶带、线缆、麦克风、扬声器或配件。 组长注意： 在将每个讲台组的箱子或设备箱搬上卡车前，请使用物料清单（BOM）核对并划掉每一项：
  • MS-1
  • ASC-01
  • WM-1
  • ALS-4