Power distribution
| Team | Keyman 🔑 | Crew |
|---|---|---|
| Power | Jeff Korell | Nico Martinez; April Korell |
Purpose Thank you for keeping everything safely powered! Your team runs mains power from the venue outlets to the A/V booth, the stage and the active speakers, and then helps cover cables.
Assignment scope
Power runs mains power only. Audio Cabling runs the audio cables. The lobby and Accounting speakers use wall sockets.
⚠️ Electrical safety
• Only a qualified person does electrical work that needs a qualification. Never change any equipment ground.
• Inspect cords, and set aside any damaged cord. Don't overload circuits.
• Never run power near the baptism area (area 11) or wet floors. If equipment must be used where it could get wet, protect it with an RCD (GFCI).
• Cover every walkway crossing, and let the teams know before switching on.
• Roll the PCS-2 (power distribution set, 50 kg) case with a helper.
Required references
- Full drawing set: CABR-2026 schematic, final draft (PDF)
- Hazard analysis: DC-83 (job hazard analysis) drafts
- Sheets for this team: 4-1 (outlets and booth route), 6-2 (active speaker power note)
- Equipment list: October BOM — cases listed below
Equipment cases
| Case | Contents |
|---|---|
| PCS-2 (power distribution set) | Power cables and sockets |
| CPS-1 (cable protection set) | Covers and rubber mats (shared with Audio Cabling) |
| CPS-3 (cable protection set) | Carpet strips (shared with Audio Cabling) |
Power schedule
| Supply | From | To | Sheet |
|---|---|---|---|
| A/V booth | Venue outlet on the left of sheet 4-1 ("Powers AV-booth") | Along the stage front, then down the centre line to the A/V booth | 4-1 |
| Stage equipment | Venue outlet on the right of sheet 4-1 | Equipment on and behind the stage, including the stage monitors (one supply for both) | 4-1, 6-2 |
| Lobby speaker | Nearest wall socket | SPK-Lobby | 6-2 |
| Accounting speaker | Nearest wall socket, away from the baptism area | SPK-Accounting | 6-2 |
The venue wireless receivers at the stage may also need power; please check with the venue technician.
Setup steps
1. Confirm outlets and loads Sheet: 4-1
- Confirm both venue outlets and the equipment loads before running cables.
- Check the wall sockets beside the lobby and Accounting speakers.
🗺️ View Sheet 4-1
Sheet 4-1 — Stage Area Large Scale View
2. Run the booth supply
- Follow the route on sheet 4-1: from the left outlet along the stage front, then down the centre line to the booth.
- Cover every walkway crossing and tape the cable flat.
3. Run the stage supply
- From the right outlet to the stage monitors and other stage equipment.
4. Lobby and Accounting Sheet: 6-2
- Use the wall socket beside each unit, and run a PCS-2 lead only if needed.
- At Accounting, keep power away from the baptism area and wet floors.
🗺️ View Sheet 6-2
Sheet 6-2 — Loudspeakers Wiring Diagram
5. Inspect and hand over
- Walk every route and check the covers.
- Let the teams know before switching on, and confirm the booth supply before the booth powers up.
6. Help with covers
- Once power is done, please help Audio Cabling cover the floor crossings.
Completion checklist
- Outlets and loads confirmed
- Booth supply run as sheet 4-1 shows
- Stage supply run; stage monitors powered
- Lobby and Accounting speakers powered
- Every crossing covered; exits clear
- Teams told before switching on
- Final check by the keyman
Dismantling
Thank you for keeping us safe! After the program on Sunday (April Korell goes to the packing team):
- Please wait for the egress and packing safety meeting with prayer, 30 minutes after the program ends.
- Switch off before disconnecting anything.
- Coil the cords neatly and pack PCS-2.
- Bring everything to the packing area; the keyman does a final check.